SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 1 04.26.19
Vive PowPak Dimming Module with
0 –10V- Control
The PowPak Dimming Module with 0 –10V- Control
is a radio frequency (RF) control that operates
0 –10V- controlled LED drivers or fluorescent
ballasts based on input from Pico remote controls
and RadioPowr Savr sensors. The Dimming Module
with 0 –10V- Control is ideal for small areas
(e.g., classrooms, conference rooms, private offices).
Communication with RF input devices (e.g., Pico
remote controls, Radio Powr Savr sensors) is
accomplished by using Lutron Clear Connect RF
Technology.
These products are also compatible with the Vive
hub which enables a simple setup process using a
standard web browser on any Wi-Fi enabled phone,
tablet or computer. It also enables control and
monitoring of all Vive devices. The Vive hub can be
added at any time. System reprogramming will be
required. For a complete list of features supported
with the Vive hub, see specification submittal
3691044-04 at www.lutron.com
Note for Replacement: RMMS- the “S” model can
replace the non-”S” model.
Features
Controls up to 60 mA of 0 –10V- controlled fixtures
together
Switches up to 8 A total
0 –10V- control link automatically sources or sinks
to the third-party fixtures
Configurable high- and low-end trim
Various operating voltages available; refer to model
number chart on next page for details on voltage
requirements
Receives wireless inputs from up to 10 Pico remote
controls, 10 Radio Powr Savr occupancy / vacancy
sensors, and 1 Radio Powr Savr daylight sensor
Utilizes Lutron Clear Connect RF Technology; refer to
model number chart below for frequency band data
Mounts to the exterior of a 100 mm x 100 mm
square junction box through a 20 mm knockout
Models
Model Number Region Operating Voltage Frequency Band
RMMS-8T-DV-B China 220 –240 V~ 868.125868.475 MHz
NOTE: Contact Lutron for frequency band compatibility for your geographic region if it is not indicated above.
1
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 2 04.26.19
Specifications
Power
Operating voltage
220 –240V~ 50 / 60Hz
Output Ratings
Switch rating of 8 A. Rated for resistive or capacitive
loads as defined by IEC/EN 60669-2-1
0 –10V- control link for 60 mA maximum output,
source or sink automatically configures
Other Power Specifications
Standby power:
220–240 V~ <1.0 W
BTU / hour when fully loaded: 9
Works with all drivers and ballasts that provide
a current source that is compliant to IEC 60629
AnnexE.2, and whose inrush current does not
exceed NEMA410 standards for electronic
driver / ballast
System Communication
Operates using Clear Connect RF Technology for
reliable wireless communication; refer to model
number chart on page 1 for frequency band details
Wireless sensors and controls must be located within
9 m of the associated control module.
Mounting
This device can be installed on a junction box
through a 20 mm knockout or with mounting
screws. The device must NOT be mounted inside a
metallic enclosure. Improper installation can result in
degraded wireless communications and intermittent
or sustained communications failures and will not
be covered under warranty. Refer to the installation
instructions and consult local and national electric
codes for proper installation.
The PowPak should be installed in an accessible
location and in a way that avoids exposure to high
voltage, particularly in those installations where
button programming is used. Record where it is
mounted so that it can be easily located later.
Metal Ceiling Mounting
Metal ceiling grids must have a > 3 mm gap of
non-metal material which extends the entire length of
the tile on at least one edge. This is often achieved
by foam spacers that are used to prevent tile-to-tile
rattling.
Metal ceiling grids which are continuous (with no
gap) or those that are interlocked, must have a total
surface area that is less than 81 m
2
for each section.
The overall space can be larger as long as there are
non-metal sections bordering or intersecting the
metal sections.
Environment
Ambient operating temperature: 0°C to 40°C
0% to 90% humidity, non-condensing
For indoor use only
All drivers and ballasts used with Vive wireless
controls must comply with EN 55015 / CISPR 15
NOTICE: Improper installation can result in
degraded wireless communication and/or
intermittent or sustained communication failures,
and will not be covered under warranty.
2
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 3 04.26.19
Specifications (continued)
0 –10V- Control Link
Communicates with up to 60 mA of fixtures
Control link is IEC SELV
0 –10V- control can be installed using basic or
double-insulated devices
Terminals accept one 0.75 mm
2
to 1.5mm
2
(18 AWG to 16AWG) solid wire
Always follow local wiring codes
Compatible with ANSI E1.3 2001 (R2006), IEC
60929 Annex E
Default Operation
Associated wireless input devices control all
connected fixtures together
Occupancy Sensors:
Occupied:100%; Unoccupied:0% (OFF)
Pico Remote Controls:
On:100%; Favorite Level:50%; Off:0% (OFF)
Daylight Sensor: Decreases electric light in response
to additional available daylight
Key Design Features
LED status indicator shows load status and provides
programming feedback
Configurable high-end and low-end trim
Power failure memory: If power is interrupted,
connected loads will return to the previous level prior
to interruption
0 –10V- control mis-wire protection up to 30V-
3
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 4 04.26.19
Advanced Configurations
Pico Remote Controls
Up to 10 Pico remote controls
Favorite levels can be set for each Pico remote control
Radio Powr Savr Daylight Sensor
The Radio Powr Savr daylight sensor will affect all
connected LED drivers and ballast equally
For multiple rows of daylighting, a separate PowPak
Dimming Module with 0 –10V- must be used for each
daylighting row
Minimum Light Level Setting (optional)
Certain applications, such as hallways, may require
that the lights never turn off. For these areas, select the
minimum light level option and the load will lower to
programed low-end level. Default operation lowers to
OFF.
High- and Low-End Trim
High-end and low-end trim affect all connected fixtures
equally, and can be configured from the PowPak
Dimming Module.
Adjustable low-end trim (0% –45%). Trimmable low-end
can ensure a stable light level. Some fixtures will flicker
or drop out if trimmed too low.
The maximum light output of connected fixtures can be
decreased down to 55% for energy savings in over-lit
spaces.
Note: The perceived light output of low-end trim may
vary between fixture manufacturers and model numbers.
For best results, do not mix different drivers or ballasts
on the same 0 –10V- circuit.
Radio Powr Savr Occupancy Sensors
Radio Powr Savr occupancy and vacancy sensors
control all connected drivers or ballasts.
Pico remote controls can be used to adjust the
occupied levels of fixtures that they control from 1% to
100% (of output signal) or can make them unaffected by
occupancy events.
Vacancy events (area becomes unoccupied) turn all
driver or ballast models off or to minimum light level.
4
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 5 04.26.19
System Diagram
Wiring Schematic
Radio Powr Savr Occupancy Sensor (up to 10)
Radio Powr Savr Daylight Sensor (up to 1)
LED Drivers Fluorescent Ballasts
010V control
To fixtures (60 mA max)
Line / Hot
Junction Box*
Switched
Line / Hot
Neutral Neutral
+
010V to LED Drivers /
Fluorescent Ballasts
To LED Drivers / Fluorescent Ballasts
20 mm trade-size knockout opening
Adaptor
* NOTE: The control module mounts to the exterior of a junction box. Do not mount inside a metallic enclosure.
Pico Remote Control (up to 10)
5
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
Vive
PowPak Dimming Module Wireless Lighting Control
3691045-04f 6 04.26.19
Dimensions
Dimensions are shown as: mm
86.9
71.6
10 0.1
Range Diagram
9 m
maximum
Radio Powr Savr
Occupancy
Sensor
Pico
Remote
Control
PowPak
Dimming Module
Install in center of room
to maximize RF coverage.
PowPak
Dimming
Module
12 m
9 m
Lutron, )Lutron, Clear Connect, Radio Powr Savr, PowPak,
Pico, and Vive are trademarks or registered trademarks of Lutron
Electronics Co., Inc. in the US and/or other countries.
NOTE: Wireless sensors and controls must be located within
9 m of the associated control module.
Metal ceiling grids must have a > 3 mm gap of non-metal
material which extends the entire length of the tile on at least
one edge. This is often achieved by foam spacers that are
used to prevent tile-to-tile rattling.
Metal ceiling grids which are continuous (with no gap) or
those that are interlocked, must have a total surface area that
is less than 81 m
2
for each section. The overall space can be
larger as long as there are non-metal sections bordering or
intersecting the metal sections.
31.8
20 mm trade-size knockout opening
112.0
Adaptor
6